LPC2368FBD100 IC MCU ARM7 LPC23 16/32B 512KB FLSH 100LQFP

LPC2368FBD100 IC MCU ARM7 LPC23 16/32B 512KB FLSH 100LQFP LPC23 ARM7TDMI-S Core 10bit ADC

Condição de LPC2368FBD100:
Item vendido no estado conforme descrição

Garantia  de  LPC2368FBD100:
3 meses direto com a Net Computadores

• Arm7TDMI-S processor, running at up to 72 MHz
• Up to 512 kB on-chip flash program memory with In-System Programming (ISP)
• 32 kB of SRAM on the Arm local bus for high performance CPU access
• 8 kB SRAM for general purpose DMA use also accessible by the USB
• 16 kB SRAM for Ethernet interface. Can also be used as general purpose SRAM
• Dual Advanced High-performance Bus (AHB) system
• Advanced Vectored Interrupt Controller (VIC)
• General Purpose DMA controller (GPDMA) on AHB
• Ethernet MAC with associated DMA controller
• Four UARTs with fractional baud rate generation
• USB 2.0 full-speed device with on-chip PHY
• CAN controller with two channels
• SPI controller
• Two SSP controllers, with FIFO and multi-protocol capabilities
• Three I2C-bus interfaces
• I2S (Inter-IC Sound) interface for digital audio input or output
• SD/MMC memory card interface
• 70 general purpose I/O pins with configurable pull-up/down resistors
• 10-bit ADC with input multiplexing among 6 pins
• 10-bit DAC
• Four general purpose timers/counters with a total of 8 capture inputs
• One PWM/timer block with support for three-phase motor control
• Real-Time Clock (RTC)
• 2 kB SRAM powered from the RTC power pin
• WatchDog Timer (WDT).
• Standard Arm test/debug interface for compatibility with existing tools
• Emulation trace module supports real-time trace
• Single 3.3 V power supply (3.0 V to 3.6 V)
• Four reduced power modes: idle, , power-down, and deep power-down
• Four external interrupt inputs configurable as edge/level sensitive
• Processor wake-up from Power-down mode via any interrupt
• Two independent power domains allow fine tuning of power consumption
• Each peripheral has its own clock divider for further power saving
• Brownout detect with separate thresholds for interrupt and forced reset
• On-chip power-on reset
• On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz
• 4 MHz internal RC oscillator trimmed to 1 % accuracy
• On-chip PLL

Maiores detalhes de LPC2368FBD100 no site do fabricante:
https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontroller

Tags de LPC2368FBD100: LPC2368FBD100K, LPC2368, LPC2368FBd100, nsd1728d, ARM7 series Microcontroller, MCU LPC2000, ARM LPC2000, ARM7TDMI-S, 10-bit ADC, 10bit ADC, conversor AD 10bits, LPC2368FBD100,551, LPC2368FBD100-551, CPU RL78 core, microcontrolador MCU RL78, microprocessador de desenvolvimento, RL78/G13-Starter-Kit, RENESAS R8C controller, RENESAS R5F controller, M3062LFGPGP, M3062LFGPGP-U3C, M3062LFGPGP-U5C, M16C/60, 16-bit Microcontrollers - MCU, M16C M16C/60/62P, M3062, M3062L, M3062LF, M3062LFGPGPU3C, QSK-62P PLUS, QUICK START KIT M16C/62P EVAL BD, M16C, SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER, MCU Arm, MCU Arm7, MCU 10Bit, LPC23, ARM7TDMIS, NXP Semiconductors, ARM Microcontrollers, LPC2364FBD100, LPC2364FET100, LPC2364HBD100, LPC2365FBD100, LPC2366FBD100, LPC2367FBD100, LPC2368FBD100, LPC2368FET100, NXP Semiconductor