The VCC5884EA from SANYO is a 1/3" CCD super high resolution DSP color camera and high resolution 540 TV lines and minimum illumination 0.5 LUX at f1.2, backlight compensation and 12V DC / 24V AC, internal sync / LI.
The VCC5884EA has a sliding ON/OFF switch that allows you to turn the automatic gain control on or off as required. The extraordinarily compact size [63 (W) x 68 (H) x 51 (D) mm] of VCC5884EA makes the camera inconspicuous and it is possible to hide it even more effectively by enclosing it in a 5-inch dome. It Runs on 24V AC or 12 to 15V DC power sources (dual power supply).

Features

1/3" CCD image sensor with approx. 410,000 picture elements.

Super high horizontal resolution of 540 TV lines for maximum detail and a noticeably sharper, clearer picture.

High sensitivity for monitoring at a minimum required illumination of 1.0 lx with F1.2 lens (AGC on).

Built-in DSP (digital signal processing) circuitry delivers superior color reproduction and reduced noise.

Backlight compensation (center-zone photometry system) luminance measured at center and automatic lens aperture adjustment enable a clear image even when backlit.

Automatic gain control - A sliding ON/OFF switch allows you to turn the automatic gain control on or off as required.

A uniquely compact design and extraordinarily compact size [63 (W) x 68 (H) x 51 (D) mm]

Auto-tracing white balance, Electronic iris for indoor use with manual or fixed iris lens. Internal/Line locks synchronizing system.

Runs on 24V AC or 12 to 15V DC power sources.

Specifications	Value
Scanning system	NTSC Standard 525 Lines, 30 frames/sec.
Image sensor	1/3” (approx. 4.8 x 3.6 mm) interline transfer method CCD
Effective picture elements	768 (H) x 494 (V)
Horizontal resolution	540 TV lines (typical)
Minimum illumination (approx.)	0.5 LUX at f1.2
Video output level	1.0 V (p-p) / 75 ohms, composite
Video S/N ratio	More than 50 dB (AGC off)
Backlight compensation	ON / OFF — Slide SW (side) ON = Multi-spot metering (64-section) / Center-zone metering — (activated when auto iris lens used)
White balance	TTL auto tracing white balance
Gain control	AGC on/off
Light control	Optical auto iris lens / Electronic iris (indoor use)
Lens mount	CS mount (top / bottom selectable)
Flange back	12.5 mm ±0.5 mm adjustment
Auto iris lens	DC type
Auto iris output	DC: Drive coil (+, –), Brake (damp) coil (+, –)
Lens iris level	LEVEL: L to H — VR (side)
Electronic iris	ON (EI) / OFF (AI) — Slide SW (side)
Electronic iris range	1.0 to 50,000 lx (with F1.2 lens)
Synchronizing system	Internal sync / Line lock — Slide SW (side)
V phase adjustment	LINE PHASE — VR (rear
Sockets	Video signal – VIDEO OUT — BNC (rear) Auto iris lens - LENS — 4-pin (side) Power supply - 24V AC, GND — Pushlock terminal x 3 (rear) 12V DC, NC — Pushlock terminal x 2 (rear)
Operating Conditions	Operating - Temperature: –10°C to 50°C [14°F to 122°F], Humidity: within 90% RH Storage - Temperature: –20°C to 70°C [–4°F to 158°F], Humidity: within 70% RH
Power requirement	24V AC, 60 Hz / 12 to 15V DC
Power consumption (approx.)	3.6 W
Camera mount	1/4” – 20 UNC (top / bottom selectable)
Dimensions (approx.)	63 (W) x 68 (H) x 51 (D) mm [2.48 (W) x 2.68 (H) x 2.01 (D) in.] (excluding protrusions)
Weight (approx.)	160 g [5.64 oz] (without lens)