Condição de WAP4410N: novo em embalagem comercial
O Acess Point Wireless N tem a função de atuar como ponte entre uma rede sem fio e uma rede tradicional. O Access point é um aparelho que transforma o tráfego da rede convencional (via cabos) em sinal de rádio Wi-Fi. Por meio do Access Points, usuários de PDAs ou notebooks equipados com Wi-Fi podem acessar a rede local da empresa ou navegar pela Internet. Com a tecnologia 802.11N a velocidade de trafego chega a 270mbps, pode ser ligado através de fonte externa de energia ou por cabo de rede PoE. Com tecnologia MIMO utiliza 3 antenas externas.
Padrão : IEEE 802.11b/g/n
Ganho : Antena: 2dBi
Portas : 1 RJ45 10/100Mbps
Segurança : WEP (64/128) bits, WPA, WPA2
Gerenciamento : Web, SNMP (v1,v2c)
Medidas embalagem (L/A/P) : 285 / 245 / 65 mm
Pesos Bruto/Líquido : 0.93 / 0.75 kg
Specifications
Standards
Draft IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af
(Power over Ethernet), 802.1x (security authentication), 802.11i security WPA/WPA2, WMM
Ports
Ethernet, Power
Buttons
Reset
Cabling type
Unshielded twisted pair (UTP) Category 5e or higher
LEDs
Power, Ethernet, Wireless, PoE
Operating system
Linux
Setup/Configuration
Web user interface
Built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
Management
Simple Network Management Protocol (SNMP) version
SNMP version 1, 2c
Event logging
Event logging
Email logging
Remote syslog
Web firmware upgrade
Firmware upgradeable through web browser
Diagnostics.
Flash, RAM, LAN, WLAN
Dynamic Host Configuration Protocol (DHCP)
DHCP client
HTTP Redirect
Redirects initial user access to an external web server to display company logo or network usage policy
IPv6 host
Support for management and control of access point over IPv6
Supports RFC2460 (IPv6 protocol) and RFC4294 (IPv6 node requirements)
Network Capabilities
Multiple BSSID
Supports up to 4 BSSIDs, allowing the creation of multiple virtual access points
VLANs
Supports 802.1q - up to 4 VLANs
SSID to VLAN mapping
Supports mapping of SSIDs to VLANs to securely separate workgroups across wireless and wired domains
Spanning Tree
Supports 802.1d Spanning Tree Protocol to prevent loops when using wireless distribution system (WDS) links as redundant links in a distribution system
Operating modes Access
point mode, point-to-point bridge mode, point-to-multipoint bridge mode, repeater mode, wireless client mode
Load balancing
Allows bandwidth control with user-defined CPU usage ratios
Auto-channel selection
On boot-up, the access point selects the least congested channel
802.11d regulatory domain
Enables the access point to provide radio channel settings for client devices, facilitating easy client access as they move across regulatory domains
Security
WEP/WPA/WPA2
Wired Equivalent Privacy (WEP) 64-bit/128-bit, WPA-Pre-Shared Key (WPA-PSK), WPA2- PSK, WPA-ENT, WPA2-ENT
Access control
Wireless connection control: MAC-based
SSID broadcast
SSID broadcast enable/disable
Client isolation
Supports wireless client isolation between and within SSIDs
802.1X
Wireless clients can be authenticated through IEEE 802.1X
802.1X supplicant
Supports 802.1X supplicant on the Ethernet port to allow the access point to authenticate itself to the network
RADIUS server
Up to 2 RADIUS servers can be configured for redundancy purposes
WPS
Supports WPS, a WI-FI Alliance specification for simple and secure setup of a wireless network
Rogue access point detection
New access points detected that have not been categorized as known are logged as rogue access points, allowing the administrator to clamp down on unapproved devices in the network
Quality of Service
QoS
4 queues
802.1p VLAN priority
WMM wireless priority
Mapping of 802.1p VLAN priority to WMM wireless priority to maintain end-to-end QoS
Wireless
Spec/modulation
Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM, 802.11n/OFDM
Channels
Operating channels: 11 North America, 13 most of Europe (ETSI and Japan)
Internal antennas
None
External antennas
3 (omnidirectional)
Transmit power
Transmit power @ normal temp range for FCC:
802.11b: 16 dBm @ 1TX, 19 dBm @ 2TX, 20.5 dBm @ 3TX
802.11g: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX
802.11n: 17 dBm @ 1TX @ MCS0~5/8~13, 13 dBm @ 1TX @ MCS6/14,
11 dBm @ 1TX @ MCS7/15, 20 dBm @ 2TX@MCS0~5/8~13,
16 dBm @ 2TX @ MCS6/14, 14 dBm @ 2TX @ MCS7/15,
21.5 dBm @ 3TX@MCS0~5/8~13, 17.5 dBm @ 3TX @ MCS6/14,
15.5 dBm @ 3TX @ MCS7/15
Transmit power @ normal temp range for ETSI:
11b/g/n: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX
Antenna gain in dBi
2
Receiver sensitivity
802.11.n: 300 Mbps at -69dBm
802.11.g: 54 Mbps at -73dBm
802.11.b: 11 Mbps at -88dBm
Environmental
Dimensions
6.69 x 6.69 x 1.60 in.
W x H x D
(170 x 170 x 40.7 mm)
Weight
0.86 lb (39 kg)
Power
12V 1A DC input, and IEEE 802.3af compliant PoE
Max power draw: 10.1W
Certification
FCC, CE, IC
Operating temperature
32- to 104-F (0- to 40-C)
Storage temperature
-4- to 158-F (-20- to 70-C)
Operating humidity
10% to 85%, noncondensing
Storage humidity
5% to 90%, noncondensing
Package Contents
Cisco WAP4410N Wireless-N Access Point with PoE
User guide on CD-ROM
Ethernet network cable
Power adapter
Product stands
Registration card
Minimum Requirements
802.11b, 802.11g, 802.11n wireless adapter with TCP/IP protocol installed per PC
Switch/router with PoE support or PoE injector when used with PoE
Web-based configuration: Java-enabled web browser
WAP4410N Access Point Cisco Wireless N PoE
Condição de WAP4410N: novo em embalagem comercial
Tags de WAP4410N: CISCO, WAP4410N, Access Point, Acces, Acess Point, Ponto de Acesso, WAP4410N-BR, Cisco Systems, Cisco Systems
